Poseidon 1250, Hw-Group, Raumüberwachung und Monitoring, High End Überwachung. Bis zu 41 Sensoren oder Kombi- Sensoren. 3 potentialfreie Ein-, 2 potentialfreie Ausgänge. Webinterface, voll SNMP fähig, Email. SMS per ext. Modem.

Poseidon 1250 is a device capable of sending e-mail when the sensor’s temperature goes out of safe range or when the contact of a connected relay closes. Besides e-mail and WWW graphical interface, also several M2M protocols are supported (SNMP, XML, Modbus/TCP etc.)

Sensors can be connected to the Poseidon model 1250 unit via two busses or you connect directly senor's contacts. The device measures values of connected sensors, the user can access the data over specialized protocols or web browser.

Poseidon can be integrated into NMS (Network Monitoring System), or used with the PD trigger software which simply alerts of a critical situation by sending an SMS message. As an alarm response, this software can close a relay (via network) that controls e.g. light signaling or alarm horn.

* Industrial bus (RS485): up to 31 sensors, up to 1 000m
* 3 Digital inputs: connect relay dry contact directly
* IT bus (1-Wire): up to 10 low cost probes, RJ11 wiring
* Sensor value out of range: sending Email or SNMP Trap to several recipients.

Die Poseidon Serie von HW group lässt sich von jedem, auch von unbedarften Benutzern, innerhalb kürzester Zeit und wenigen Minuten aufsetzen. Nachdem die Sensoren angesteckt sind einfach die IP Adresse des Gerätes im Browser öffnen und einloggen. Wie das geht ist ausführlich beschrieben und innerhalb weniger Handgriffe erledigt.

• WEB (HTML)
  Values and state of sensors are presented on WWW page. The page is automatically reloaded every 5 second. There is a link to Flash Setup from main HTML page, update FirmWare and others.
• XML
  All sensor's values as well as alarm status information are available in XML files (temper.xml) and any application can log it from XML tags
• SNMP
  SNMP is protocol for monitoring of telecommunication devices, network infrastructure and related technology. The Poseidon is fully controllable over SNMP (v1, partially v2)
• Modbus/TCP
  Modbus/TCP is industrial standard for input from sensors and output to visualizing and SCADA systems. All values are available over Modbus/TCP

 
• Alarms
  • SNMP Traps
    In case of contact switch or exceeding of "Safe Range", the sensor get to the Alarm status. To notify of this a SNMP Trap including alarm status description is sent to configured IP address
  • Email
    In case of contact switch or exceeding of "Safe Range", the sensor get to the Alarm status. To notify of this a Email including alarm status description is sent to configured email address

• Binary Input (Dry Contact inputs)
  3x input to connect door contact or relay output (NO or NC)
• IT Bus (RJ12 1-Wire)
  Inexpensive interface to connect up to 10 temperature probes over a total distance of 10 meters or less
• Industrial bus (RS-485)
  Industrial interface, up to 31 sensors up to 1 000 meters. The temperature, humidity and other sensors. The converters to current loop (4 to 20 mA) or platinum temperature sensors Pt100, Pt500, Pt1000 (2,3 or 4 conductor).

• 2x outputs
  The Poseidon 1250 supports two outputs for two external relay controlling. The outputs can be controlled over network (Flash Setup, XML, SNMP).
  • Output – Alarm status link: DTR output can be used for alarm signalization of any sensor. Warn light or horn can separately, independently on other software, signal critical status.

We recommend to use: PowerEgg, P1250 RC (Relay Cable), DIN relay

Technical specifications of the Poseidon 1250

• Ethernet: RJ 45 - 10BASE-T / 10 Mbit/s
• Port 1: Industrial bus (RS-485 / RJ45)
• Port 2: IT bus (1-Wire / RJ12)
• Port 3: RS-232 (connector Cannon 9 Male)
• 3 Dry contact input: terminal board for contact (0 to 500W)  
• Device setting:
  • Locally - RS-232 Setup
  • UDP Config
  • Over HTTP - graphic interface Flash
  • Over SNMP